
Bitümento BT2K 750
Dual component, flexible, water based, fibre reinforced rubber-polymer modified bitumen waterproofing BT2K 750 waterproofing has been designed for protection of structures against water with carefully chosen rubber-polymer modified bitumen, dual component, cold applied, fibre reinforced and flexible waterproofing material.
PLACES OF USE
- Waterproofing of concrete, brick, stone, briquette, plastered or similar mineral surfaces.
- Foundations, basements, foundation walls.
- Terraces and balconies and similar wet spaces.
TECHNICAL SPECIFICATIONS
- Density of Mixture: 1.1 kg/lt
- Heat resistance: 100°C
- Waterproof after full cure (in accordance to EN 15814 – W2B)
- Application Temperature Range: +2°C / +35°C
- Pot Life: 1-2 hrs • Curing time: approx. 24 h (at 20 °C)
- Full curing time: 3 days
SURFACE PREPARATION
Application surface to be dry or damp. Application must not be carried out during precipitation, and wet or icy surface conditions. Surface must be cleared from debris, paint, salt, dust, loose particles, and oil. Surface irregularities must be repaired using a proper repair mortar. All 90° corners should be rounded for proper application.
APPLICATION
Apply ready-mixed BT2K 750, diluted with 3:10 with water, or the bitumen emulsion BTR200, diluted 1:2 with water or liquid component of BT2K 750 diluted 1:5 - 1:10 with water, to the substrate. Application: Apply only on surfaces to be in contact with water. Add powder component slowly while mixing liquid component in its pail with a low rpm mixer (e.g., 400 – 600 rpm) until having a homogenous and non-flocculent mixture. As the primer completely dries out, the mixture is applied to surface with brush or trowel or suitable pulverizing equipment at 2-6 mm thickness. In case of double-layer application, the first layer should be allowed for curing and then the second layer should be applied. It is recommended to use with 50-100 gr/m2 fiberglass or net to improve mechanical properties in large areas and horizontal and vertical joints and to bridge the cracks. Mixture should be used within 1-2 hrs. depending on temperature. Application tools should be rinsed with water immediately after application. Tool cleaning with solvents may be employed for tools not cleaned on time. Protect surfaces for 24 hrs from precipitation, freezing and direct sunlight after application.
PACKAGING
Both components in 32 kg pails (Liquid 24 kg, Powder 8kg.)
STORAGE CONDITION AND SHELFLIFE
12 months in un-opened original pails. Production date printed on pails.
WARNINGS
- Do not inhale cement based powder component.
- Gloves and goggles must be worn at all times.
- Rinse well with water in case of skin and eye contact.
- Immediately contact a physician for eye irritation.
- Empty pails must not be used for potable water and food storage.
BTM Bitümlü Tecrit Maddeleri Sanayi ve Ticaret A.Ş. Kemalpaşa O.S.B. Mahallesi Gazi Bulvarı No:152 35730 Kemalpaşa/İzmir TURKEY Phone:+90 232 877 04 02 Fax:+90 232 877 04 10 info@btm.co • www.btm.co
Technical documents
Technıcal Data Sheets
- PDFBT2K 750Request document
Declaratıon of Performance
- PDFDOP3: EN 15814 BT2K750Request document
Products in the same group

Bitümento BT2K 500
Brush Applied, Water Based, Flexible, Two Component Waterproofing Material enhanced with Polymers and Reinforcing Fibres Flexible waterproofing material free of solvents and reinforced with fiber as well as polymer, rubb

Bitümento BT2K 600
Bitumento BT2K 600 is a solvent-free, two-component, elastic, water-based, fiber reinforced, rubber and cement based bitumen waterproofing material. More ...

BT2K 600 PLUS
Polymer-modified bitumen-rubber based, two-component, fiber-reinforced, flexible, high-viscosity liquid waterproofing material, applicable by brush or spray machine. More ...

Alüsol ALS 100
Containing Reflective Aluminum, Single-Component, Bitumen Based Waterproofing Material. More ...