
BTM Poseidon PO5000
POSEIDON PO 5000 is a bitumen-based waterproofing membrane enriched with elastomeric and TPU additives, with a special carrier with high stability and increased mechanical resistance, PE (polyethylene film) on the lower surface, and colored mineral or fine sand on the upper surface.
PLACES OF USE
•On terrace roofs, inclined roofs of structures,
•On curtain walls, it is used for providing basement tanking, water tightness, and moisture proofing.
•Poseidon PO5000 is designated for outstanding performance in many climatic zones thanks to its outstanding flexibility in cold weathers and high temperature resistance in hot weathers. It is used as the bottom and middle layer membrane in waterproofing.
•Poseidon PO5000 is used on wet areas such as bathroom-kitchen and the foundations having pressure or non-pressure underground or surface waters.
SURFACE PREPARATION
The surface where BTM Waterproofing Membrane Poseidon PO5000 is to be applied should be cleaned from dust, dirt, rust, and oil; loose pieces should be scraped off. Depending on the surface where BTM Waterproofing Membrane Poseidon PO5000 is to be applied, when necessary, BTS 100 or BTR 100 primer should be applied to the surface; it should be waited to get completely dry.
APPLICATION
If concrete, the surface where BTM Waterproofing Membrane Poseidon PO5000 is to be applied should be with floated and trowelled gradient finish, and be clean and dry. Before BTM Waterproofing Membrane Poseidon PO5000 application, bitumen solution primer BTS 100 (TS103) or bitumen emulsion primer BTR 100 (TS113) should be applied to the surface and should be waited to get completely dry.
Coating application is started by the lowermost part of the roof (lowermost layer) and the application is made vertical to the gradient. Waterproofing membrane Poseidon PO5000 is stuck to the surface by torch. Crossing should absolutely be made between the rows. Lapping margin should be left; 15 cm for 1 meter short edge lapping, 10 cm for long edge lapping. Joints should be well stuck. Between the layers, crossing should be made as 50 cm for short edge, 5 m for long edge.
PACKAGING
BTM Waterproofing Membrane Poseidon PO5000 is offered to the market in roll form; 1 m width, 8 m length.
STORAGE CONDITION AND SHELFLIFE
The membrane rolls should be stored vertically under a roof, protected from direct sunlight. If the rolls have to be stored outdoors for a long period of time, they must be covered with a protective layer in order to protect them from the sunlight. The membrane rolls or pallets should not be stacked on each other.
BTM Bitümlü Tecrit Maddeleri Sanayi ve Ticaret A.Ş. Kemalpaşa O.S.B. Mahallesi Gazi Bulvarı No:152 35730 Kemalpaşa/İzmir TURKEY Phone:+90 232 877 04 02 Fax:+90 232 877 04 10 info@btm.co • www.btm.co
Technical documents
Technıcal Data Sheets
- PDFPoseidon PO5000PDF ↓
- PDFPoseidon PO5000 MineralPDF ↓
- PDFPO 5000 SandPDF ↓
- PDFPoseidon PO 4000 SandRequest document
Products in the same group

BTM Elastobit
BTM Elastobit is a fiberglass or polyester felt reinforced waterproofing membrane made of bitumen modified by SBS (styrene-butadiene-styrene), resistant to plant roots, the lower surface is coated with PE (polyethylene)

BTM Plastobit
Plastobit is a fiberglass or polyester felt reinforced waterproofing membrane made of bitumen modified with APP (atactic polypropylene), the lower surface is coated with PE (polyethylene) film and the upper surface is co

BTM Plastobit PP4000V
BTM makes available in its range of products the viaduct type sheeting with a thickness of 4 mm and high tensile strength manufactured specially for such insulation applications thanks to its expertise in waterproofing.

BTM Polibit
BTM Polibit is a fiberglass or polyester felt reinforced waterproofing membrane made of bitumen modified with APP (atactic polypropylene), the lower surface is coated with PE (polyethylene) film and the upper surface is